node-mcp23017_with_i2c_updated

node-mcp23017_with_i2c_updated
=============

Node.js library for the I2C I/O Expander MCP23017 on a Raspberry Pi

It currently only supports reading from and writing to the chip

The module tries to mimic the Arduino-Syntax

##Installation

install via npm. just type the following in the terminal/console

```bash
npm install node-mcp23017_with_i2c_updated --save
`

Raspberry Pi Setup

In order to use this module with the Raspberry Pi running Raspbian you have to enable to stuff


``bash
$ sudo vi /etc/modules
``

Add these two lines

``bash
i2c-bcm2708
i2c-dev
``

``bash
$ sudo vi /etc/modprobe.d/raspi-blacklist.conf
``

Comment out blacklist i2c-bcm2708

``
#blacklist i2c-bcm2708
``

Load kernel module

``bash
$ sudo modprobe i2c-bcm2708
``

Make device writable

``bash
sudo chmod o+rw /dev/i2c*
``

Usage

$3

Pins are numbered from 0-15 where 0-7 is register A and 8-15 is register B

`javascript
var MCP23017 = require('node-mcp23017_with_i2c_updated');

var mcp = new MCP23017({
address: 0x20, //default: 0x20
device: '/dev/i2c-1', // '/dev/i2c-1' on model B | '/dev/i2c-0' on model A
debug: true //default: false
});

/*
By default all GPIOs are defined as INPUTS.
You can set them all the be OUTPUTs by using the pinMode-Methode (see below),
You can also disable the debug option by simply not passing it to the constructor
or by setting it to false
*/

//set all GPIOS to be OUTPUTS
for (var i = 0; i < 16; i++) {
mcp.pinMode(i, mcp.OUTPUT);
//mcp.pinMode(i, mcp.INPUT); //if you want them to be inputs
}

mcp.digitalWrite(0, mcp.HIGH); //set GPIO A Pin 0 to state HIGH
mcp.digitalWrite(0, mcp.LOW); //set GPIO A Pin 0 to state LOW

/*
to read an input use the following code-block.
This reads pin Nr. 0 (GPIO A Pin 0)
value is either false or true
*/
mcp.digitalRead(0, function (err, value) {
console.log('Pin 0', value);
});

``

Example (Blink 16 LEDs)

`javascript
var MCP23017 = require('node-mcp23017_with_i2c_updated');

var mcp = new MCP23017({
address: 0x20, //all address pins pulled low
device: '/dev/i2c-1', // Model B
debug: false
});

/*
This function blinks 16 LED, each hooked up to an port of the MCP23017
*/
var pin = 0;
var max = 16;
var state = false;

var blink = function() {
if (pin >= max) {
pin = 0; //reset the pin counter if we reach the end
}

if (state) {
mcp.digitalWrite(pin, mcp.LOW); //turn off the current LED
pin++; //increase counter
} else {
mcp.digitalWrite(pin, mcp.HIGH); //turn on the current LED
console.log('blinking pin', pin);
}
state = !state; //invert the state of this LED
};

//define all gpios as outputs
for (var i = 0; i < 16; i++) {
mcp.pinMode(i, mcp.OUTPUT);
}

setInterval(blink, 100); //blink all LED's with a delay of 100ms
```

TODO

- implement built-in pullup resistors
- implement interrupt handling

Acknowledgement

some parts are derived from the module https://github.com/x3itsolutions/mcp23017 by x3itsolutions (Fabian Behnke)