Particle Core & Photon IO Plugin for Johnny-Five
npm install particle-io
Particle-io is a Firmata-compatibility IO class for writing node programs that interact with Particle devices (formerly Spark). Particle-io was built at Bocoup
In order to use the particle-io library, you will need to load the special
voodoospark firmware onto your
device. We recommend you review VoodooSpark's Getting Started before continuing. There is also a screencast of how to get started: Get Your Motor Running: Particle Photon and Johnny Five.
We also recommend storing your Particle token and device ID in a dot file so they can be accessed as properties of process.env. Create a file in your home directory called .particlerc that contains:
``sh`
export PARTICLE_TOKEN="your particle token"
export PARTICLE_DEVICE_ID="your device id"
Then add the following to your dot-rc file of choice:
`sh`
source ~/.particlerc
Ensure your host computer (where you're running your Node.js application) and the Particle are on the same local network.
The "Hello World" of microcontroller programming:
`js
var Particle = require("particle-io");
var board = new Particle({
token: process.env.PARTICLE_TOKEN,
deviceId: process.env.PARTICLE_DEVICE_ID
});
board.on("ready", function() {
console.log("Device Ready..");
this.pinMode("D7", this.MODES.OUTPUT);
var byte = 0;
// This will "blink" the on board led
setInterval(function() {
this.digitalWrite("D7", (byte ^= 1));
}.bind(this), 500);
});
`
#### Troubleshooting
If your board is connecting, but the board.on("ready", ...) event is not occuring, ensure the wifi network you are connected to allows for direct TCP client/server sockets (this form of communication is often blocked by public wifi networks).
Particle-io can be used as an IO Plugin for Johnny-Five:
`js
var five = require("johnny-five");
var Particle = require("particle-io");
var board = new five.Board({
io: new Particle({
token: process.env.PARTICLE_TOKEN,
deviceId: process.env.PARTICLE_DEVICE_ID
})
});
board.on("ready", function() {
console.log("Device Ready..");
var led = new five.Led("D7");
led.blink();
});
`
See the above Troubleshooting section if your board is connecting, but the board.on("ready", ...) event is not occuring.
, deviceName, or host/port. Both deviceId and deviceName require an additional token so that the host and port of the device can be retrieved from the Particle cloud.Example:
`js
var Particle = require("particle-io");var byId = new Particle({
token: process.env.PARTICLE_TOKEN,
deviceId: process.env.PARTICLE_DEVICE_ID
});
var byName = new Particle({
token: process.env.PARTICLE_TOKEN,
deviceName: process.env.PARTICLE_DEVICE_NAME || "crazy_pickle"
});
var byIp = new Particle({
host: '192.168.0.111',
port: 48879
});
`device properties
You can get the information that the component knows about the chip with some read-only device properties. This is useful for retrieving the IP address of the Particle so that you can swith over to
/port mode if necessary.The available properties are:
-
deviceId: The ID of the device
- deviceName: The name of the device
- deviceIp: The IP address of the device on the local network
- devicePort: The port the device is listening on for connectionsExample:
`js
var Particle = require("particle-io");var board = new Particle({
token: process.env.PARTICLE_TOKEN,
deviceName: process.env.PARTICLE_DEVICE_Name || "crazy_pickle"
});
board.on("ready", function() {
console.log(
"Connected to " + board.deviceName +
" (" + board.deviceId + ") " +
"at " + board.deviceIp + ":" + board.devicePort
);
});
`MODES
> The
property is available as a Particle instance property:`js
var board = new Particle(...);
board.MODES;
`
- INPUT: 0
- OUTPUT: 1
- ANALOG: 2
- PWM: 3
- SERVO: 4pinMode(pin, MODE)
> Set a pin's mode to any one of the MODES.
Example:
js
var board = new Particle(...);board.on("ready", function() {
// Set digital pin 7 to OUTPUT:
this.pinMode("D7", this.MODES.OUTPUT);
// or just use the integer:
this.pinMode("D7", 1);
});
`PWM Support (Servo support is also limited to these pins):
- Core pins: A0, A1, A4, A5, A6, A7, D0, D1.
- Photon pins: A4, A5, D0, D1, D2, D3
- P1 pins: A4, A5, D0, D1, D2, D3
digitalWrite(pin, value)
> Sets the pin to
or 0, which either connects it to 3.3V (the maximum voltage of the system) or to GND (ground).Example:
`js
var board = new Particle(...);board.on("ready", function() {
// This will turn ON the on-board LED
this.digitalWrite("D7", 1);
// OR...
// This will turn OFF the on-board LED
this.digitalWrite("D7", 0);
});
`analogWrite(pin, value)
> Sets the pin to an 8-bit value between 0 and 255, where 0 is the same as LOW and 255 is the same as HIGH. This is sort of like sending a voltage between 0 and 3.3V, but since this is a digital system, it uses a mechanism called Pulse Width Modulation, or PWM. You could use analogWrite to dim an LED, as an example. PWM is available on D0, D1, A0, A1, A4, A5, A6 and A7.
Example:
js
var board = new Particle(...);board.on("ready", function() {
// Set an LED to full brightness
this.analogWrite("A7", 255);
// OR...
// Set an LED to half brightness
this.analogWrite("A7", 128);
});
`servoWrite(pin, value)
> If the value is less than 544, sets the pin to a value constrained between 0 and 180, where the value represents degrees of the servo horn. If the value is 545 or greater, sets the pin to a value in microseconds.
Example:
js
var board = new Particle(...);board.on("ready", function() {
// Move a servo to 90 degrees
this.servoWrite("D0", 90);
});
`js
var board = new Particle(...);board.on("ready", function() {
// Set the servo duty cycle to 1759 microseconds
// Note that the servo pwm frequency is 50mhz and
// the default servo range is 600-2400 microseconds
this.servoWrite("D0", 1759);
});
`servoConfig(pin, min, max)
> Sets the range for the servo PWM duty cycle. The default range is 600 - 2400 microseconds. Can be called instead of pin mode.
Example:
js
var board = new Particle(...);board.on("ready", function() {
this.servoConfig("D0", 690, 2310);
});
`
digitalRead(pin, handler) Setup a continuous read handler for specific digital pin (D0-D7).
> This will read the digital value of a pin, which can be read as either HIGH or LOW. If you were to connect the pin to a 3.3V source, it would read HIGH (1); if you connect it to GND, it would read LOW (0).
Example:
js
var board = new Particle(...);board.on("ready", function() {
// Log all the readings for D1
this.digitalRead("D1", function(data) {
console.log(data);
});
});
`
analogRead(pin, handler) Setup a continuous read handler for specific analog pin (A0-A7). Use with all analog sensors
Example:
js
var board = new Particle(...);board.on("ready", function() {
// Log all the readings for A1
this.analogRead("A1", function(data) {
console.log(data);
});
});
``